Undermount sink installation in Fort Pierce happens on countertop day: we mount the sink to the underside of the new granite or quartz, polish the cutout to match the edge, and seal the joint so water can't creep between sink and stone. Sink work belongs to every kitchen remodeling in Fort Pierce North job we take, and the sink is planned before a single cut is made.
The sink has to be on site before we template, because the cutout is cut to that exact bowl. If the sink sits in a small kitchen, our condo kitchen remodel page covers space-saving choices, and for a top-to-bottom project the sink is one line in a full kitchen remodel.
Part of our kitchen remodeling in Fort Pierce North services.
What's Included
Sink work with us is part of the countertop job, not a separate trip. During the estimate visit we open the sink cabinet, measure its inside width and check the floor of the cabinet for old leak damage, because a soft base will not carry a heavy bowl. You choose the sink, or bring one you already own, and it has to be in the house before we template: the cutout is traced from that bowl, and faucet, soap and filter holes are marked where you want them. Back at the shop the opening is cut and its edge polished to match the countertop edge. On install day an undermount sink is bonded and clamped to the underside of the stone, and the seam between bowl and stone is sealed so water cannot work into the joint. Apron-front sinks get a support frame inside the cabinet first. The estimate states in writing how the faucet and drain are reconnected.
- Advice at the estimate on sink type and size for your cabinet base and stone
- Template with your sink on site, so the cutout follows the actual bowl, not a catalog drawing
- A polished cutout and faucet holes drilled where you want them
- Undermount sink bonded and clamped to the stone, with the joint sealed
- A clear note on the estimate about how the faucet and drain are reconnected
What Tells You the Sink Should Change With the Countertop?
If you are replacing the tops anyway, the sink is the cheapest it will ever be to change, because the old one comes out with the old counter. In older Treasure Coast kitchens these are the problems we see that make the case:
- A drop-in sink whose caulk line around the rim stays black with mildew through the humid months
- A rusted or pitted rim on an old stainless drop-in bowl
- Porcelain-on-steel chipped through to dark metal near the drain
- A cabinet floor that is stained or soft from a slow drain leak
- A single bowl too small for sheet pans, or a double bowl too narrow for either side to be useful
- Old polybutylene or corroded supply lines that are easiest to replace while the base is open
Any one of those can be lived with. Paying to set a tired sink under brand-new stone is the step most owners regret later.
Undermount, Farmhouse or Workstation: Which Sink Fits Your Cabinet?
The cabinet under the sink decides more than the catalog does. A standard sink base suits most undermount sinks; an apron-front sink needs the cabinet front cut down or a purpose-made base; a workstation sink needs a wide enough base and a ledge that clears the faucet.
| Sink | Cabinet need | Stone work | Living with it |
|---|---|---|---|
| Stainless undermount | Standard sink base | Polished cutout; sink bonded and clamped below | Wipes crumbs straight in; quiet with sound pads |
| Farmhouse / apron front | Cut-down or apron-ready base with added support | Stone wraps three sides; front left open | Big basin; heavy fireclay needs a solid frame |
| Workstation | Wide sink base to suit the longer bowl | Larger cutout; ledge must align with the stone edge | Accessories slide on a built-in ledge |
How Is a Farmhouse Sink Cutout Made in Granite or Quartz?
For an apron-front sink, the stone stops at the sink's sides and back, and the sink's front face becomes part of the cabinet front. The sink sits on a support frame inside the cabinet, set to the right height so the stone rests on the sink rim evenly. A fireclay farmhouse sink is heavy, so that support is built before we template.
Because farmhouse sinks vary in size and squareness, the cutout is measured from your sink, not from the spec sheet. Small differences in a handmade fireclay bowl show up as uneven gaps if the stone is cut from drawings.
Sink Replacement With a New Countertop: Who Handles What
We cut the stone, set the sink and seal it. The water supply and drain are plumbing. St. Lucie County lets a sink be swapped without a permit only if it stays where it was (St. Lucie County Government); relocating it, say into a new island, calls for licensed plumbing and a permit.
- Before template: sink and faucet bought and on site, old sink still working
- Tear-out day: water shut off, old top and sink removed
- Install day: new top set, sink mounted and sealed, faucet holes ready
- Hookup: faucet and drain reconnected as arranged in your estimate
Silicone needs time to cure before the sink takes full weight, so we will tell you when it is safe to fill the basin.
Talk to the shop before you buy a slab.
Free in-home estimates · Mon–Fri 7:00–4:30 · weekend estimates by appointment
How the Job Runs, Step by Step
- Call with the sink in mind. Tell us the sink you have or want, and whether the countertop is being replaced at the same time.
- Free estimate visit. We look at the sink base, measure, and confirm the sink style suits the cabinet and the stone.
- Written quote. The quote names the cutout, faucet holes, sink mounting and how the plumbing reconnection is arranged.
- Template with fixtures. Your sink and faucet are on site so the cutout and holes are measured from them.
- Cut, mount and seal. The cutout is cut and polished at our shop, then the sink is mounted, sealed and left to cure.
Questions about kitchen sink installation? Call the shop.
Free in-home estimates · Mon–Fri 7:00–4:30 · weekend estimates by appointment
What Affects the Price
Sink work is priced on your countertop estimate in writing after we measure the base and see the sink. The main things that change it:
- Sink style: an apron-front or workstation cutout takes more work than a standard undermount
- Cabinet changes, such as cutting down a sink base for a farmhouse sink
- Number of faucet, soap and filter holes drilled in the stone
- Support framing for heavy fireclay or cast iron sinks
- Whether the sink stays in place or moves, which brings in licensed plumbing
- A bowl wider than the existing base, which means a new sink cabinet as well as a new cutout
- Removing an old undermount bonded to stone, or a drop-in set in mortar-bed tile
- Disposal and dishwasher connections, which involve licensed plumbing or electrical work
- Who supplies the sink: one you bring, or one we provide and list on the estimate
Licensed Plumbing, Permits and the Kitchen Sink
Cutting and mounting a sink in stone is countertop work, which Florida DBPR does not require a state license for. Plumbing is a licensed trade under DBPR, so any change to supply lines, the drain or the trap arm belongs to a licensed plumber, and so does a disposal circuit on the electrical side.
For a permit, location decides. Unincorporated addresses fall under St. Lucie County's Building & Code Regulation Division; within Fort Pierce city limits a plumbing permit is its own filing, apart from any building permit, under City of Fort Pierce rules. In a condo, ask the association how water to your unit is shut off before install day.
Why VD Quality Design for Kitchen Sink Installation
- The person who measures your sink base, Victor, is the owner of the shop that cuts the stone
- Google reviewers say the crew left the kitchen clean once the tops and sink were in
- 4.9 stars from 31 Google reviews, with several customers noting quick turnaround from measure to finished kitchen
- Free in-home estimates during weekday hours from 7:00 a.m., with Saturday appointments set up whenever you ask for one
- An A+ BBB rating, and you can pay with cash, a check, Zelle or a debit or credit card once every line of the written estimate is agreed
Reviews From Kitchen Sink Customers
V.D Quality Design Granite & Marble holds a 4.9-star average from 31 Google reviews (checked November 2026).
“VD Quality Design Granite was professional, reasonably priced and got the job done in no time. They cleaned up after themselves. I wouldn’t hesitate to use them again and appreciate their quality work.”
“I am quite satisfied with the work performed by VD Quality Design. They are professionals, they give good price and a reasonable work time.”
“They took the time to answer all our questions and helped us pick the right quartz to update our kitchen. They had great communication and were always on time. They took great care in measuring and installing. Left everything perfect.”
Where We Install Kitchen Sink Installation
We cut sinks into new tops throughout Fort Pierce and Port St. Lucie, as well as in Lakewood Park and Vero Beach South.
- Fort Pierce North: A few minutes from the shop, so templating with your new sink on site is easy to schedule.
- Fort Pierce: Older kitchens with drop-in sinks, where a new stone top is the moment to go undermount.
- Port St. Lucie: Builder-grade stainless drop-ins in newer homes, traded for undermount or workstation bowls.
- Lakewood Park: Homes near 55+ communities, where a shallower bowl saves bending at the sink.
- Vero Beach South: 1970s–90s neighborhoods where original porcelain sinks have chipped down to the steel.
- Vero Lake Estates: Large-lot homes on well water, where mineral crust builds up around old faucet holes.
- River Park: Canal-side 1960s–70s homes, where we check the sink base for old drain leaks before mounting.
- White City: Roomy ranch kitchens with space for a farmhouse sink in a wider, reinforced base.
- Hutchinson Island South: Oceanfront condo towers, where the water shutoff for a sink swap may need building staff.
- Indian Harbour Beach: Canal-front kitchens in Indian Harbour Beach put the sink under a water-view window, so the undermount cutout matters.
Kitchen Sink Installation FAQs
Do you supply the sink or can we bring our own?
You can bring your own, and many owners do. Have it delivered before the template so we cut the opening from the actual bowl. If you want help choosing, Victor will tell you at the estimate which sizes and styles suit your cabinet and stone, and anything we provide appears as its own line on the written estimate.
Can a farmhouse sink go into an existing cabinet?
Often, if the sink base is wide enough. The cabinet's front panel is cut down to fit the apron, and a support frame is added inside to carry the sink's weight. Some older cabinets are too narrow or too weak for that, and we check yours at the estimate before you buy the sink.
Who reconnects the plumbing after the countertop install?
That depends on the job and is settled in writing before install day. We mount and seal the sink; the faucet supply lines and drain are plumbing, and moving them is licensed work. At the estimate we explain how reconnection is handled for your kitchen so you are never left without a working sink.
Which sink type works best with quartz?
A stainless or composite undermount is the usual pairing, because the polished quartz edge shows all the way around the bowl and wipes clean. Farmhouse and workstation sinks also work. Avoid setting a hot pot straight onto quartz beside the sink; the resin can scorch, so keep a trivet nearby.
Can you replace just the sink without new countertops?
Swapping an undermount sink under an existing stone top is difficult, because the old sink is bonded to the stone and the new bowl must match the cutout. It is usually done when the countertop is replaced. If your top is staying, tell us the situation and we will say honestly whether it is practical.
Related Services
Kitchen Remodeling
Learn more →
Condo Kitchen Remodel
Condo kitchen remodels on the Treasure Coast: HOA paperwork, elevator-friendly slab delivery and quiet-hours scheduling.
Learn more →
Full Kitchen Remodel
Full kitchen remodels in Fort Pierce: tear-out, cabinets, stone countertops, backsplash and sink hookup coordinated start to finish.
Learn more →